ViProje


 MENÜ
 
  • Anasayfa
  • Malzeme Bilgisi
  • Forum
  • Downloads
  • Linkler
  •  

     Language
         

    Google Translate

     

     Tüm Projeler
     

     

     Dost Likler
      · 1: İkinciElKamyonlar.CoM
    · 2: Menacam.CoM
    · 3: PiCProje
    · 4: OselSan.CoM
    · 5: Saltnlight-e.CoM
     

    2W 88-108mhz TX with PLL Input - FM PLL Modülatörler - ViProje. CoM - NET
    FM PLL Modülatörler 2W 88-108mhz TX with PLL Input

    Güzel tasarlanmış bir vco. Modülasyonu iyi olduğunu düşünüyorum. Tasarlayan kişi harici pll kullanmayı düşünerek tasarlamış. Bu yüzden pll voltaj girişi ve pll frekans çıkışı var. mpx ve mono girişlerini ayrı bırakmış. MPX ten RDS girmekte sakınca yok. Kesinlikle profesyonel değil. Ancak birçok profesyonel cihazdan güzel vco tasarımı var. Güzel deneyimler yaşana bilir bir kart. Rdvv a ait sadece pll kartını kullana bilirsiniz. Pira.cz ye ait saa1057 li pll sini kullana bilirsiniz. UKW Radiosender in LM7001 kullanarak yaptığı dip switch li pll sini kullana bilirsiniz. PCB Boyutu 53 x 100 mm

    L1 = 4 Turns Air coil, internal diameter 8 mm, 1 mm CuL (approx. #18 A.W.G.), wirespacing 1 mm - the 1uH and 2.2uH coils are ready-made molded type coils - all 'square' drawn capacitors are MKT or MKP-types, the rest are (multilayer) ceramic ones - all resistors 0.25 Watts, unless otherwise indicated - the 470-Ohms trimmer resistor is from the brand Piher, horizontal mount, 10 mm diameter - the BF960 mosfet and the BFR96(S) transistor are mounted at the bottomside (copperside/ trackside) of the printed circuitboard - be sure to use an appropriate heatsink on the 2N4427 rf-transistor! - the PLL-input accepts a (stabilized and filtered) control voltage of 0-12 Volts DC for the desired frequency variation or can be connected to an individual synthesizer.

    PCB

    2W 88-108mhz TX with PLL Input pcb

    PCB LayOut

    2W 88-108mhz TX with PLL Input pcb layout

    PCB üst yüz

    2W 88-108mhz TX with PLL Input pcb top

    PCB Üst Yüz

    2W 88-108mhz TX with PLL Input pcb component

    2W_88-108mhz_TX_with_PLL_Input.rar

    Kaynaklar

    http://www.facebook.com/pages/Fm-TRANSMITTER-Broadcast-Free-RADIO-88-108Mhz-TX-RDS-encoderlinear-ecc/151343845691

    http://pira.cz/

    http://www.senderbau.egyptportal.ch/

    Gönderen: Hüseyin GÜNER Tarih: 07/05/2013 2W 88-108mhz TX with PLL Input Yazdır

    Yorumu Gönderen : Herbert Tarihi : 25/05/2013 01:18 pm

    Heh, it all depends First, I wdulon't dare trying to design a 4GHz RF design on a two-layer board it's just not practical if you want good performance and reliability. For four layers, it depends on your layer stack. The four-layer service I use (Laen's DorkbotPDX PCB order) has a stack-up of approximately 10 mils between the outer and inner layers, and about 40 mils for the center core (joining the top and bottom layer pairs together). It depends on how sensitive your design is, and how much loss you can afford between devices. If your VCO+PLL is pumping out +10dBm at 4GHz and your mixer requires +0dBm input, you'll probably do fine sending that signal across a few inches of PCB. But at a distance of inches, 4GHz is well into transmission line territory, so you'll have to get your trace widths right given your PCB material Er and trace-to-ground distance.I'd spend as much time as possible staring at reference designs for high-frequency mixers and PLL+VCOs. They're usually done on four- or six-layer FR4. A lot can be learned from observing things that are clearly intentional ( Why are there a billion vias between ground layers here? ) and trying to understand them.I'd also start small, building each component as a separate PCB project. Sending 4GHz off-board isn't too big a deal if you're careful, keep the traces short, get your transmission line impedance right, and are willing to accept a few dB loss. There's a LOT of learning you can do with a board that's a bit lossy but otherwise works just fine. Then, when you have the design nailed, you can tackle integrating it with other components on the same board.I'd be happy to review your schematic/board as you go, if you'd like. I don't claim to be an experienced RF engineer, but RF is kinda an obsession of mine, and I've developed enough intuition and understanding to build successful 3GHz boards.
    İsim/Nic:
    E-mail: (optional)
    Smile: smile wink wassat tongue laughing sad angry crying 

    Onay Kodu


     Anket
       

    Sitemizde Bir Forum Açılmasını İstermisiniz??
    Evet Güzel Olur.
    Hayır Gerek Yok.
    Bir Fikrim YOK.
    Sonuçlar

     Tüm Kategoriler

     

     

     

     

    Bu site Hüseyin GÜNER tarafından çeşitli scriptler bir araya getirilerek yazılmıştır. Tüm hakları saklıdır.

    WebHost 000WebHost.Com




    www.000webhost.com